Specifications:
Nominal voltage: 12 VDC
Nominal power: 8 W
Maximum head: 2.3 M (3.3 PSI)
Maximum flow: 9 l/min (143 GPH)
Connection size: 9/16” NPT
Electrical connector: 3-pin (fan header style)
Motor type: Brushless DC*
Pump bearing type: Polished Sapphire
Size: 2.1”W x 2.1”H x 1.75”D
Weight: 241 g (8.5 oz)
*Includes 1/2" High-Flow Barbs*
Description:
The Danger Den CSP-MAG 12 volt pump is a highly efficient
pump packed into a tiny 2.1" x 2.1" x 1.75" Acetal housing. the CSP-MAG
was designed to surpass the performance of the its predecessor, CSP-750, by
providing an extremely long service life, without increasing the size.
This pump is recommended for watercooled setups with minimal flow restrictions.
The CSP-MAG will work great with Danger Den's Maze 4 coolers.
Features:
• Extreme Service Life: This pump is designed with extreme service life (50,000
hours*) This was accomplished by employing several different design patent
pending techniques.
• Bearings: The MAG features dual in fluid bearings, using the best material
available, jewels. These bearings are made of highly polished Sapphire. This is
an extremely hard and long lasting material, often found in expensive watches,
high precision instruments, and gyroscopes used in the aerospace and military industries. The MAG is the first liquid cooling pump to utilize this technology.
• Reducing Forces: The MAG design utilizes two natural pump forces to reduce
bearing / shaft loads. First a small amount of flow is diverted through and
around the impeller between the motor rotor and stator. This allows boundary
layer effect of the spinning rotor surface to help stabilize radial loads. This is similar
to how the bearings in your automobile works. As an additional effect
it keeps coil temperatures low allowing the motor to run at maximum efficiency.
Magnetic forces developed between the very strong rare earth magnetic rotor
ring, and the iron stator teeth allow the impeller to operate in magnetic suspension, which virtually eliminates thrusting loads.
• Leak Proof: The MAG has no shaft seal, eliminating the possibility of leaking
occurring due to long term seal ware. The stator assembly has a plastic barrier
between the rotor and the fluid operating on magnetic coupling. The drive and
impeller housing is plastic, to reduce the chance of long term fouling.
• Brushless DC motor: The MAG features a brushless DC motor designed with an
operational component life in excess of 50,000 hours. All heat generating
components are thermal conductive bonded to the aluminium case. This provides a
large heat sink area allowing the motor to run under constant high efficiency.
• Small Size: The CSP-MAG dimensions are 2.1” x 2.1” x 1.75" when compared to a
typical 110V pumps the CSP-MAG uses considerably less space, leaving room in
your case for additional components . We still have the smallest pump currently available to the PC
liquid cooling consumer.
• Configurable: The CSP-MAG features an easy to exchange impeller. This will
allow us to provide different impellers for the various types of cooling blocks
on the market. C-Systems is working closely with the cooling block manufactures
to provide specific impellers for there products
• Direct RPM: The CSP-MAG features a hall sensor that directly reads the rotation
of the impeller. The impeller RPM can be monitored using your standard fan mother
board utilities via the fan port.
• Power Suppy: The MAG requires 12V DC and is equipped with a Tx3 connector.
• Ultra low noise: The CSP-MAG operates at a lower noise level the our
CSP-750MKII due to the sealed motor compartment and improved pump
housing design.
• Easy Installation: Purchase the industrial velcro to mount anywhere in case.
• Flow Direction: The MAG features a side inlet and top outlet for flow
direction. The pump is now available with 1/2" OD High Flow straight
fitting.
• Ports: The MAG features a top outlet and side. The pump is now available with
9/16-18 straight fitting ports.
• Finish: The MAG features a new Acetal housing to ensure long term
corrosion protection.
|
|
